On this page
SimpleFOC QtFOC v1.6

QtFOC is a tiny, open-source, low-cost BLDC driver board in the form factor of the Seeed Studio XIAO and Adafruit QT Py boards. You plug in a XIAO or a QT Py, connect a motor and a power supply, and you have a complete FOC motor controller in a 25 x 45mm footprint, fully compatible with the SimpleFOClibrary.
The board generates its own 5V from the motor power supply and powers the microcontroller from it, so once the board is programmed it doesn’t need a USB cable or an extra regulator.
Get started with your board GitHub project

What can it run?
The XIAO / QT Py format has few pins, but enough for a complete FOC setup:
- A motor: a BLDC motor, or a stepper motor with the
HybridStepperMotorclass (SimpleFOClibrary v2.3.5+) - A position sensor: SPI (on the JST connector), encoder, I2C or PWM, see the limitations
- Current sensing: low-side current sensing on two phases
- Communication: USB, or Serial on the UART header
Features
- DRV8316C integrated 3-phase driver - datasheet
- Hardware configured, no SPI configuration needed
- 3PWM mode
- Protections: undervoltage lockout, charge pump fault, overcurrent (~16A), overtemperature
- Input voltage: 8-35V
- Current: up to 8A peak (DRV8316 limit), the continuous current depends on cooling
- Current sensing: low-side, phases A and B, 150mV/A, about ±11A range with a 3.3V ADC
- Power supply voltage sensing: VIN/11 on
A2 - Onboard 5V buck converter: powers the XIAO / QT Py from VIN through a diode, so USB and VIN can be connected at the same time (200mA max)
- SPI connector: 6-pin JST SH for SPI position sensors (AS5047, AS5048A, MT6701, MT6835, …)
- UART / GPIO header:
3V3,GND,RX,TX - Fault LED and power LED
- Compact: 25 x 45mm, with 4 mounting holes for M2 screws
- Open source: designed in EasyEDA - EasyEDA project, all fabrication files on GitHub
- Low cost: about the same as the SimpleFOCMini, around 10$
Limitations
- Low-side current sensing is not supported on all microcontrollers, see the compatible boards. Without it, use voltage torque control.
- Few free pins: once the motor, the current sensing and the voltage sensing are connected, only
D6(TX) andD7(RX / CS) and the SPI pinsD8-D10are left.- With an SPI sensor, only
D6is free. - An encoder needs both
D6andD7, so it can’t be used together with an SPI sensor or the UART header. - The I2C pins of the header (
D4/D5) drive the motor. I2C sensors can be connected to the STEMMA QT connector of QT Py boards that have a separate I2C bus.
- With an SPI sensor, only
- 5V buck converter: up to 200mA, enough for the MCU and the sensor, but not for the WiFi / BLE radio of ESP32 boards. If you use WiFi or BLE, also power the MCU board from USB.
Mounting holes
The board has four 2mm mounting holes, for M2 screws or standoffs, in the corners of a 21 x 36mm rectangle:

- Board size: 25 x 43mm, plus about 2mm for the SPI connector tab
- Hole diameter: 2mm, plated
- Hole spacing: 21mm across the board, 36mm along it
The spacing across the board (21mm) is the same as on the SimpleFOCMini, so both boards fit the same rail or bracket width.
The holes are connected to GND
The plated mounting holes are connected to the board’s ground. If you mount the board on a metal frame, the frame is connected to GND too, so make sure nothing else on the frame is at a different potential.
Compatible boards
Any board with the XIAO / QT Py pinout fits. Here is a non-exhaustive list:
| Board | MCU | Supported by SimpleFOC | Low-side current sensing |
|---|---|---|---|
| QT Py SAMD21 XIAO SAMD21 | SAMD21 | ✔️ | ✔️ (v2.3.5+) |
| QT Py ESP32-S3 XIAO ESP32-S3 | ESP32-S3 | ✔️ | ✔️ |
| QT Py ESP32 Pico | ESP32 | ✔️ | ✔️ |
| XIAO ESP32-C6 | ESP32-C6 | ✔️ | ✔️ |
| QT Py RP2040 XIAO RP2040 | RP2040 | ✔️ | ❌ |
| XIAO RP2350 | RP2350 | ✔️ (v2.3.5+) | ❌ |
| QT Py ESP32-S2 | ESP32-S2 | ✔️ | ❌ |
| QT Py ESP32-C3 XIAO ESP32-C3 | ESP32-C3 | ✔️ | ❌ |
| XIAO nRF52840 | nRF52840 | ✔️ | ❌ |
| QT Py CH32V203 | CH32V203 | ❌ | ❌ |
See the microcontroller support docs for more details.
QtFOC or Mini?
Both boards use the DRV8316, so they have the same power stage. The SimpleFOCMini is a standalone driver that you wire to any microcontroller. QtFOC is a shield for XIAO / QT Py boards, with the wiring, the 5V supply for the MCU and the sensor connector already on the board.
| Feature | SimpleFOCMini v2.3 | QtFOC v1.6 |
|---|---|---|
| Board | ![]() | ![]() |
| Driver | DRV8316 | DRV8316 |
| Supply voltage | 5-35V | 8-35V |
| Current sensing | 3 phases, low-side | 2 phases, low-side |
| Voltage sensing | ✔️ | ✔️ |
| Power for the MCU | 3.3V LDO, 20mA | 5V buck, 200mA |
| Sensor connector | ❌ | SPI (JST SH) |
| Microcontroller | Any, wired with jumpers | XIAO / QT Py, plugged in |
| Size | 24 x 25mm | 25 x 45mm |
Release history
| Version | Date | Changes |
|---|---|---|
| v1.0 | 07/25 | First version, the MCU needs a separate power supply |
| v1.6 | 02/26 | First public release: MCU powered from the DRV8316 buck converter (5V) |
How to get one
- Order the assembled board: coming soon from Makerfabs.
- Make it yourself: the board is fully open source: the Gerber, BOM and pick and place files are in the GitHub repository, and the EasyEDA project can be ordered directly from JLCPCB. The process is the same as for the SimpleFOCMini, see the Mini fabrication guide
